toolguy (86)
Made by C-L USA, 27/64" and 17/32", new condition, pair $30 or bundle with the other set listed for a total of $120. More deals when you click on too...
Cal Pump Model A430, up to 430 gallons per hour, motor runs in oil bath, operates in any position, corrosion resistant, new cost well over $100. Mo...
Heavy duty Wolf made in England, 7" capacity, 4200 RPM, so not too fast for sanding, 7.6 amp, comes with pin and shaft wrench. More tools when you ...
Sapphrite ceramic type nozzle, hole size is 7/32" and 3 3/4" long, both look unused, pair $10. More deals when you click on toolguy.
In 2 piece, Loomex runs in the middle and gives protection if you want to run the wire across the floor, 48" long, tabs in each end can be cut off i...
4 Wheels with a 1" hole, 1/8" thick, diameter range 8"- 10 3/4", one has an arbor of 3/4", diameter 9", so 5 wheels $5. More deals when you click on ...
16 Piece set with tool roll, 1/4"- 1 1/4", the 7/8" is not WESTWARD, price works out to only $3.75 each, new cost for this set is well over $200. If ...
35mm Sharp, 25mm Sharp Carbide cutter, pair $25. More tools when you click on toolguy.
High & Low heat setting, 380F tip temperature, 3 new glue STICKS. More tools when you click on toolguy.
4 Old hammers, small versions of their larger ones, claws are all in good condition, one might be a ferriers and one is a Maydale which started makin...
12" Hacksaw and a jab saw for tight spots, pair $5. More tools when you click on toolguy.
High speed steel, taper 26mm-40mm, sharp and in good condition. More deals when you click on toolguy.
4 Dark 10H and 10 clear, the works $10. More deals when you click on toolguy.
Slip & Lock Nut wrench, opens to 3", in as new condition. More tools when you click on toolguy.
Greenlee USA, 1 1/8" diameter and 1/2" conduit size which is about 7/8", cutting edges look good, pair $20. More tools when you click on toolguy.
Type of stiff spring material, if you can use them it's a deal at $5 for 10. More deals when you click on toolguy.
6 Pieces, 3 or 4 styles, the works $10. More deals when you click on toolguy.
20 Amp 125 volt 3 wire twist lock connectors on a short cord, these are top quality Hubbell connectors, common size for generators, have another se...
Lock out scissor and panel breaker lock out, works on various types of breakers, pair $5, have 2 more of the breaker devices for $5. More deals when y...
These fit a standard hammer drill chuck, 1/8", 5/32", two 3/16", three 1/4", three 5/16", two 3/8", two 1/2", total 14 drills $12, also have a 5/8" & ...
6 Ft of galvanized 1/2" N.C, $10 each 6ft. piece or three for $25. More deals when you click on toolguy.
This is a Jet SD-1300, FWD-REVERSE- LOCK positions, overall length is 18" and 13" when closed. More tools when you click on toolguy.
Mounted stones, drum Sanders, wire wheel and 2 spare sanding sleeves, all have 1/4" shaft, all $17, works out to less than $1.50 each. More deals whe...
Chicago Pneumatic oscillating cutter/knife, blades are made 8n Germany by Fein, for windshield rubber removal, with several blades and wrenches. Mor...
5 Chisels 1/4"-1", four are made in England, not sure about the 1/4". More tools when you click on toolguy.
toolguy
Gerard Volk
Victoria
Tools